Why separate similar-looking reels
Reels or removed runs that look alike can be very different products. Differences in printed designation, conductor count, pair count, shielding, jacket type, and fitted ends change how an item is identified and matched to manufacturer records. Combining unlike reels into one footage total leads to inaccurate inventory and mismatched expectations during review.
Follow the capture and split workflow below so every inventory line represents a genuinely matching specification rather than an assumption made from co‑location in a tray.
Glendale’s economic-development page provides facility context. The same official page identifies aerospace/aviation/defense, advanced business services, healthcare/bioscience, manufacturing, and technology/innovation as targeted industries or industry areas. Those industry references do not establish a customer, a control-cable lot, or local purchasing demand; they only explain why a seller may be organizing facility records.
- Printed designation (TC, TC‑ER, PLTC, etc.) is primary evidence of product family.
- Conductor and pair counts must be recorded separately; a 12‑conductor cable is not interchangeable with two 6‑conductor assemblies.
- Shielding and jacket differences affect product classification and must not be merged.
- Each reel or continuous cut length should stand alone with its own measured footage and photo reference.
Step 1 — Capture the designation
Transcribe the full printed designation from the cable jacket. Where available, capture the manufacturer and the complete part number and any voltage marking. If the print is partial or worn, photograph the jacket close‑up and note which characters are unreadable.
Required evidence fields: printed designation, manufacturer, part number, voltage marking. If any of these are missing, mark them as unknown and attach photos and notes so reviewers can assess the certainty.
- If designation is unreadable: record the segment you see, mark characters as illegible, and include a photo reference.
- Do not assume Type TC based on tray location alone — rely on actual jacket marking or matching manufacturer documentation.
Step 2 — Split unlike configurations
List conductor count, pair count, gauge, shielding, jacket type, and fitted ends for each item that genuinely shares the same combination. Create separate inventory lines whenever any of those attributes differ.
Required evidence fields: conductor/pair count, gauge, shielding, jacket/fitted ends. If shielding is unclear from the jacket, note shielding as unknown and supply close‑up photos of the jacket and any cut end.
- Record conductor and pair counts exactly (for example: 12 conductors vs. 6 pairs).
- If gauge marking is missing, document how gauge was estimated (visual note) and mark it as estimated.
- Keep fitted end details (terminals, glands, lugs) with the specific reel or cut length it was found on.
Step 3 — Tie quantity to the item
Record each reel or continuous cut length with its own reel/line ID, measured length when possible, and a clear photo reference. Note whether quantity is measured or estimated and keep measured footage separate from estimated footage in inventory.
Required evidence fields: reel/line ID, continuous length, quantity basis, photo reference. Do not use a single photo to represent unlike reels; photograph each reel or visually distinct cut length.
- Label reels with a unique identifier, and if you move reels between locations, update the record to preserve chain of custody.
- When only estimated footage is available, mark the entry as estimated and include the estimation method used.
Step 4 — Disclose history and records
Separate uninstalled, unused stock from removed cable and note visible jacket damage, service history, and any applicable data sheets or manufacturer records. Attach matching records to the exact inventory line they correspond to.
Required evidence fields: uninstalled/removed state, service history, damage, matching record. If service history is unknown, document who provided access and any visible signs of wear or repair.
- Keep data sheets or part pages tied to the matching printed designation and part number.
- For removed cable with uncertain history, disclose whether fitted ends appear factory‑installed or were field‑terminated.
Handling unknown or incomplete inventory
If markings, shielding, or lengths are unknown or only partially legible, be explicit: mark fields as unknown, attach photos, and list which evidence fields are missing. The recommended buyer workflow is to treat those items as separate inventory lines with an unknown‑level flag rather than merging them into broader totals.
When inventory is incomplete, the documented resolution is to preserve each reel or continuous piece as its own quantity record and match any available manufacturer records to the specific item. This prevents the common mistake of aggregating dissimilar cable into a single footage total.
- Do not consolidate items that lack confirmed matching evidence — keep them separate and flagged for review.
- If only one reel shows legible markings, do not assume identical designation for adjacent reels without confirmation.
Illustrative record (fictional example)
Label: CT‑GJ‑EXAMPLE. Product: TC‑ER marking; 12 conductors, 16 AWG. Quantity: 240 ft continuous, measured. Condition: removed cable; fitted ends present; shielding unknown.
This fictional entry shows how a single continuous length is recorded with designation, conductor count, measured footage, condition, and a note where shielding is unknown. Use that pattern for each reel or continuous cut you document.
- Attach a photo of the printed designation and a photo of the cut end or fitted end.
- Include a reel/line ID and indicate measured vs estimated footage.
