WIRE & CABLE BUYING INQUIRIESCOMMERCIAL / INDUSTRIAL

saleselectricalbuyers@gmail.com
Electrical cable reels — illustrative inventory photograph

SELL YOUR SURPLUS / MATERIAL-SPECIFIC BUYING

Control & Tray Cable Buyers in Santa Rosa, California

We buy control and tray cable from Santa Rosa, California sellers when each reel is described by its actual construction. Send the full jacket legend, conductor or pair count, gauge, shielding detail, continuous footage, condition, and release information. Separate look-alike reels instead of presenting one combined total so the buying review can follow the material record.

Control and tray specifications Santa Rosa, California

SELLER TASK / BEFORE YOUR QUOTE

Which multi-conductor or multi-pair reels are genuinely the same specification and can be presented on the same inventory line.

THE PROBLEM TO RESOLVE

A closeout can combine multi-conductor and multi-pair reels whose count, gauge, shielding or jacket designation differs even when the cable looks alike.

MAKE THIS DECISION

Which multi-conductor or multi-pair reels are genuinely the same specification and can be presented on the same inventory line.

Evidence to have ready

  • complete jacket legend
  • designation
  • manufacturer
  • part number
  • conductor/pair count
  • gauge
  • shielding
  • jacket
  • reel reference
  • continuous length
  • quantity basis
  • fitted ends
  • photo reference
  • matching data sheet
  • unknown fields
  • condition/history

Avoid this record: All cable removed from a tray is labeled Type TC and combined into one footage total.

Better record: Use actual jacket markings and separate each specification and continuous piece; previous location does not establish product type.

Illustrative only — not a purchased Santa Rosa lot

Worked inventory record

reference
SR-CT-04
designation
TC-ER marking; 12 conductors, 16 AWG; shielding unknown
quantity
240 ft measured
condition
removed cable; fitted ends present

BUILD YOUR INVENTORY

One reel. One line.
A clearer quote request.

Keep each continuous length distinct. Two 100-foot pieces are not one 200-foot run. Record unknown markings or quantities as unknown; do not change, cut or test material to complete this worksheet.

Start with the blank inventory CSV. Use a spreadsheet or the optional worksheet below. Add labels and photo references to your records; email photographs separately to saleselectricalbuyers@gmail.com.

Do not classify cable by the tray it came from

Cable that shared a tray, rack, or project room may not share a specification. Type TC, TC-ER, PLTC, and other designations belong in the record only when they are printed on the jacket or supported by a document tied to that reel. Begin with a clear photo of the complete readable legend, manufacturer, and part number rather than the cable’s former location.

The recurring mistake is to label every cable removed from a tray as one Type TC line and add its footage together. Correct it by creating a separate inventory line for every distinct printed designation. When a legend is unreadable, record the visible characters and use “unknown” for the missing classification.

  • Complete jacket legend
  • Manufacturer and part number
  • Printed designation such as TC or TC-ER when present
  • Photo reference for each reel

Split the inventory where construction changes

Conductor count, pair count, gauge, shielding, and jacket construction are separate buying-review fields. A 12-conductor cable is not interchangeable with a 12-pair cable, and a shielded line should not be grouped with an unconfirmed one. Keep every meaningful difference on a different line even if the reels have the same color or were stored together.

Describe shielding only to the level the record supports. If the jacket or matching product record does not identify a shield, use “unknown” rather than opening or altering the cable. The point is an honest product record that can be checked against the offered reel.

  • Conductor or pair count
  • Gauge
  • Shielding stated or unknown
  • Jacket designation and visible condition

Preserve one continuous length per record

Assign a reference to every reel and cut length. State remaining continuous footage and label the quantity measured, documented, or estimated. Fitted ends, cut ends, and visible jacket damage should be noted because they describe the actual piece without making a condition or suitability promise.

Do not let several short pieces become one long length in a combined total. If a partial reel and a cut coil have identical markings, keep their quantities and condition notes distinct. That distinction is what allows the lot to be reviewed as it physically exists.

  • Reel or piece reference
  • Continuous footage and quantity basis
  • Full reel, partial reel, or cut-length status
  • Fitted ends and visible condition

Match documents to the same line item

Use the inventory reference in every photo filename and in the name of any data sheet. Attach a product record only when its manufacturer and part number can be matched to the photographed reel. A sheet for a similar cable can be supplied as background, but it cannot fill an unsupported count, shield, or designation field.

The City of Santa Rosa describes Santa Rosa as the economic center of the North Bay and highlights manufacturing, health care, technology, professional services, tourism and creative industries. That is limited context for organizing a commercial or industrial closeout; it does not identify a local seller or establish a cable specification.

  • Inventory reference repeated in files
  • Matching data sheet, if available
  • Unknown fields stated plainly
  • Storage and release notes for the actual lot

Illustrative control-cable line

Illustrative inventory example—not a purchased lot: SR-CT-04 records a reel with a TC-ER marking, 12 conductors, 16 AWG, 240 feet measured, and fitted ends. Its shield field remains unknown because the visible legend and matching record do not resolve it.

The example shows why a precise line is better than a broad “tray cable” total. It contains only what the reel record supports, preserves the unknown field, and does not use the example as a claim about a real Santa Rosa lot.

  • Reference: SR-CT-04
  • Designation: TC-ER; 12 conductors, 16 AWG
  • Quantity: 240 feet measured
  • Condition: removed cable with fitted ends

Before the first call

Your questions,
answered.

Is cable found in a tray automatically Type TC?

No. Tray location is not a product designation. Photograph and transcribe the actual jacket legend, then use the printed designation or a matching manufacturer record. If neither resolves the type, record it as unknown.

When should similar reels remain on separate lines?

Use separate lines whenever conductor count, pair count, gauge, shielding, jacket legend, condition, or continuous length differs. Similar color or storage location does not establish that two reels are the same product.

How should shielding uncertainty be recorded?

Mark shielding as unknown if it is not stated in a readable legend or matching product record. Include the reel reference, photos, and any document scope. Do not alter the cable to infer a construction detail for the inventory list.

What should I send with a mixed control-cable closeout?

Send one line per distinct specification with a photo reference, full readable marking, conductor or pair count, gauge, shielding status, continuous footage, quantity basis, condition, storage location, and release authority.

Sources

Further reading

  1. City of Santa Rosa — Doing Business
Call now