WIRE & CABLE BUYING INQUIRIESCOMMERCIAL / INDUSTRIAL

saleselectricalbuyers@gmail.com
Electrical cable reels — illustrative inventory photograph

SELL YOUR SURPLUS / MATERIAL-SPECIFIC BUYING

We Buy Control & Tray Cable in Athens, Georgia

We buy control and tray cable in Athens, Georgia, when the inventory keeps each multi-conductor assembly distinct. Record the printed designation, conductor or pair count, gauge, shielding, jacket details, fitted ends, and continuous footage by reel. Similar-looking material should remain on separate lines until markings and records show the construction is the same.

Control and tray specifications Athens, Georgia

SELLER TASK / BEFORE YOUR QUOTE

Do the records preserve the actual control or tray designation and separate each materially different assembly?

THE PROBLEM TO RESOLVE

Multi-conductor facility or industrial stock can be accidentally combined when conductor count, pair count, gauge, shielding and jacket markings differ.

MAKE THIS DECISION

Do the records preserve the actual control or tray designation and separate each materially different assembly?

Evidence to have ready

  • designation
  • manufacturer
  • part number
  • marked voltage
  • conductor count
  • pair count
  • gauge
  • shielding
  • jacket
  • fitted ends
  • reel ID
  • continuous length
  • quantity basis
  • full/partial/cut length
  • source/status
  • service history
  • jacket damage
  • record match

Avoid this record: All cable removed from a tray is classified as Type TC and similar-looking reels are merged.

Better record: Use actual markings and manufacturer records; separate unknown designation and every differing count, gauge or shield arrangement.

Illustrative fictional inventory example—not a purchased lot

Worked inventory record

reference
CT-A-01
product
TC-ER marking, 12 conductors, 16 AWG; shielding unknown
quantity
240 ft continuous, measured
condition
removed cable; fitted ends present
documentation
part number data sheet not yet matched

BUILD YOUR INVENTORY

One reel. One line.
A clearer quote request.

Keep each continuous length distinct. Two 100-foot pieces are not one 200-foot run. Record unknown markings or quantities as unknown; do not change, cut or test material to complete this worksheet.

Start with the blank inventory CSV. Use a spreadsheet or the optional worksheet below. Add labels and photo references to your records; email photographs separately to saleselectricalbuyers@gmail.com.

Transcribe the designation that is actually printed

Begin each line with the visible jacket designation, such as TC, TC-ER, PLTC, or other wording exactly as it appears, then add manufacturer, part number, and marked voltage if present. Where the legend is incomplete, capture the readable portion in photos and mark the designation unknown rather than assigning a familiar category from storage location.

Cable placed in a tray is not automatically Type TC. The inventory task is to preserve what the product says about itself, not to infer a designation from where it was installed or stored.

  • Exact jacket designation
  • Manufacturer and part number when visible
  • Marked voltage and readable jacket legend photos

Separate the differences inside similar assemblies

Create separate lines whenever conductor count, pair count, gauge, shielding, jacket, or fitted ends differ. A reel with 12 conductors at 16 AWG and unknown shielding is not interchangeable with an otherwise similar reel that has a documented pair count or different shield arrangement. Keep unknowns in their own field so they do not disappear in a combined description.

The likely inventory mistake is merging every removed cable from a tray under one Type TC label. The resolution is to use actual markings and manufacturer records, leaving unknown designation and every differing count, gauge, or shield arrangement separate.

  • Conductor count and pair count as separate fields
  • Gauge, shielding, jacket, and fitted-end differences
  • A separate line whenever an identification field is unknown

Tie partial lengths to the physical reel

List each full reel, partial reel, and cutoff with a reel ID or assigned reference, continuous length, and quantity basis. If several pieces came from the same reel, identify the origin but keep the pieces as separate lengths. Do not present a sum of cutoffs as one continuous run.

Use measured, documented, or estimated as the quantity basis. When footage is estimated, state why and retain the photographs and reference that could support a later measurement. This turns an incomplete line into an honest one instead of an assumed specification.

  • Reel ID or assigned reference
  • Full, partial, or cutoff status
  • One continuous length and its quantity basis

Record source and condition without deciding suitability

State whether the item is uninstalled maintenance stock, project overrun, or removed material, and note any known service history, visible jacket damage, and matching documents. Describe fitted ends as observed; do not turn a condition note into a performance claim. A data sheet or work record belongs with the same reel reference it actually covers.

UGA Facilities Management says more than 800 personnel manage, operate and maintain campus landscapes, buildings and infrastructure.

This is limited local facilities context, not a statement that UGA owns, offers, or endorses any cable. It explains why a seller should keep facilities-origin notes and construction records with the actual control or tray cable line.

  • Source or status: uninstalled, overrun, or removed
  • Visible jacket condition and fitted ends
  • Record-match status for data sheets or work files

Worked example and a practical submission route

Illustrative fictional inventory example—not a purchased lot: CT-A-01; TC-ER marking; 12 conductors, 16 AWG; shielding unknown; 240 ft continuous, measured; removed cable with fitted ends present; part-number data sheet not yet matched. The record does not relabel the unknown shield or assign the reel a different product family.

For an Athens inquiry, keep photo filenames tied to CT-A-01 or the seller’s own reference, then send the inventory and photos to saleselectricalbuyers@gmail.com or use the quote form. Include the release contact and any site-access constraint as a fact to be clarified, not as an assumed movement arrangement.

  • Photographs of printing, reel, and fitted ends
  • Unmatched documents marked as unmatched
  • Release contact and access facts stated separately

Before the first call

Your questions,
answered.

Is all cable found in a tray Type TC?

No. Record the actual TC, TC-ER, PLTC, or other jacket wording and keep an unreadable line marked unknown. The storage or installation location is background, not a substitute for the product designation.

Which fields should remain separate for control cable?

Keep conductor count, pair count, gauge, shielding, jacket, and fitted ends in separate fields. Create a new inventory line when any of those values differs or is unknown, even if two reels look alike from a distance.

Can similar reels be combined?

Only after the jacket legend, manufacturer or part number, and construction fields show they are the same assembly. Until then, give each reel a reference, continuous length, and quantity basis rather than merging footage.

How should removed cable with fitted ends be described?

State that it is removed, describe the observed fitted ends and jacket condition, record the known service history if any, and tie the data to a reel reference. Do not infer Type TC, condition, or continuity from the fitted end.

Sources

Further reading

  1. UGA Facilities Management Division
Call now