WIRE & CABLE BUYING INQUIRIESCOMMERCIAL / INDUSTRIAL

saleselectricalbuyers@gmail.com
Electrical cable reels — illustrative inventory photograph

SELL YOUR SURPLUS / MATERIAL-SPECIFIC BUYING

Control & Tray Cable Buyers in Cary, North Carolina

Industrial Wire Buyer: we buy control and tray cable in Cary, North Carolina. Send clear jacket-marking photos, part numbers, conductor or pair counts, gauge, shielding details, each continuous length, and visible condition. Keep different multi-conductor variants on their own lines so a review does not mistake a tray location or similar appearance for an actual product designation.

Control and tray specifications Cary, North Carolina

SELLER TASK / BEFORE YOUR QUOTE

Are the product designation and multi-conductor differences traceable to each offered reel or continuous piece?

THE PROBLEM TO RESOLVE

Similar-looking multi-conductor reels or removed runs can differ by Type TC/TC-ER marking, pair or conductor count, gauge, shielding and jacket.

MAKE THIS DECISION

Are the product designation and multi-conductor differences traceable to each offered reel or continuous piece?

Evidence to have ready

  • printed designation
  • manufacturer
  • part number
  • voltage marking
  • conductor/pair count
  • gauge
  • shielding
  • jacket
  • reel/line ID
  • continuous footage
  • quantity basis
  • fitted ends/condition
  • document reference
  • matching basis
  • service history
  • unknown fields

Avoid this record: All cable removed from a tray is classified as Type TC and combined into one footage total.

Better record: Use the actual marking and preserve each conductor/pair configuration and continuous piece separately; storage location is not product proof.

ILLUSTRATIVE ONLY — not a purchased Cary lot

Worked inventory record

line
CT-CY-01
identity
TC-ER marking; 12 conductors, 16 AWG; shielding unknown
quantity
240 ft continuous, measured
condition
removed cable; fitted ends present

BUILD YOUR INVENTORY

One reel. One line.
A clearer quote request.

Keep each continuous length distinct. Two 100-foot pieces are not one 200-foot run. Record unknown markings or quantities as unknown; do not change, cut or test material to complete this worksheet.

Start with the blank inventory CSV. Use a spreadsheet or the optional worksheet below. Add labels and photo references to your records; email photographs separately to saleselectricalbuyers@gmail.com.

What we need first

Start by photographing and transcribing the printed designation on each reel or continuous piece. Capture TC, TC-ER, PLTC or any other actual printed marking; do not assume product type from storage location or how the cable was routed.

Record manufacturer name, part number, and any voltage marking visible on the jacket. If a marking is unreadable, mark it as unknown rather than guessing. These fields form the primary evidence that ties an offered piece to a product designation.

The Town's At Work page names Epic Games, Deutsche Bank, American Airlines, LORD Corp., Verizon, John Deere, Kellogg's and Siemens among Cary businesses. Those names provide only commercial context; they do not identify cable stock, sellers, customers, or buyer relationships.

  • Evidence fields to supply: printed designation, manufacturer, part number, voltage marking
  • Provide high-resolution photos of the printed text on the jacket plus an overall reel or length view

Keep variants on separate lines

Even when reels look similar, split entries when conductor or pair counts, gauge, shielding or jacket differ. Treat each distinct conductor/pair configuration or shielding state as its own line item with its own measured footage and identity.

Document conductor or pair count, conductor gauge (AWG), presence and type of shielding, and jacket material. If shielding cannot be determined visually, mark shielding as unknown and note any fitted ends that show shield termination.

  • Evidence fields to supply: conductor/pair count, gauge, shielding, jacket
  • Use unique reel/line IDs to keep records traceable (example line IDs are acceptable)

Record continuous footage and fitted ends

List every reel or cut length with a reel/line ID, measured or documented continuous footage, and the basis for quantity (e.g., measured continuous feet vs. number of identical reels). Indicate whether fitted ends are present and describe visible jacket condition.

If a run has been cut into multiple pieces, record each continuous piece separately, including measured footage for each piece and any differences in end fittings or jacket damage.

  • Evidence fields to supply: reel/line ID, continuous footage, quantity basis, fitted ends/condition
  • If footage is estimated, state that explicitly and mark the field as estimated in the record

Attach documents and mark unknowns

Where available, attach manufacturer datasheets, purchase or inspection records, and service history to the exact line they support. Indicate the matching basis — serial numbers, part numbers, or label text used to tie a document to a line.

If a field cannot be confirmed from markings or documents, mark it Unknown rather than merging it into another line. This prevents the common mistake of combining all removed tray cable as a single Type TC total.

  • Evidence fields to supply: document reference, matching basis, service history, unknown fields
  • Do not use storage location as proof of product designation or configuration

How to present a clean submission

Provide a spreadsheet or photo-backed list where each row is one reel or continuous piece and includes: reel/line ID, printed designation photo reference, manufacturer, part number, conductor/pair count, gauge, shielding, jacket type, measured footage, fitted-ends note, and attached documents or datasheet references.

If pieces are visually identical and fully documented by the same printed designation and part number, you may present them as grouped lines but only after confirming all required evidence fields match exactly.

  • Required evidence checklist: printed designation; manufacturer; part number; voltage marking; conductor/pair count; gauge; shielding; jacket; reel/line ID; continuous footage; quantity basis; fitted ends/condition; document reference; matching basis; service history; unknown fields
  • When in doubt, split into separate lines and mark unknowns explicitly

What to do with unknown or incomplete inventory

If you cannot read a printed designation or a part number, supply close-up photos and flag the designation field as Unknown. Provide as many corroborating details as you can: measured footage, conductor count, gauge, visible shield termination, and photos of both jacket print and cross-section of a fitted end if available.

Do not combine unknown or unreadable pieces into totals with known-designation pieces. Instead create separate 'unknown-designation' lines with clear notes about which evidence is missing and which photos or documents you can provide later.

  • Actionable step: mark unreadable designation fields Unknown and attach clear photos
  • Actionable step: separate unknown-designation pieces into their own lines rather than merging with known-designation lines

Before the first call

Your questions,
answered.

Is every cable found in a tray Type TC?

No. Do not assume tray location equals Type TC. Follow step 1: photograph and transcribe the printed designation from each reel or continuous piece. If a marking shows TC or TC-ER, record it; if the marking is different or unreadable, mark the designation field accordingly. If you cannot read the marking, supply close-up photos and create a separate 'Unknown designation' line rather than combining it with confirmed Type TC footage.

Which pair, conductor and shielding differences require separate lines?

Create separate lines whenever conductor/pair count, conductor gauge, or shielding differs. Use step 2 as your rule: even visually similar reels must be split by conductor/pair count, gauge, shielding and jacket type. For each line, supply the conductor/pair count, AWG, shielding state (or 'unknown' with photos), and measured footage so each line is independently verifiable.

Should similar-looking reels be combined?

Only combine reels when every required evidence field matches exactly across them. Before grouping, confirm printed designation, manufacturer, part number, conductor/pair count, gauge, shielding and jacket match. If any of those fields are unreadable or differ, keep them as separate lines and note which fields are unknown.

What if I accidentally combined all removed tray cable into one total?

If that mistake has occurred, correct it by reopening your record and splitting the combined total into distinct lines per steps 1–3. Use photos, fitted-end details and any service or purchase documents to assign footage and identities to each line. Mark fields that cannot be verified as Unknown rather than keeping them merged; the resolution is to preserve each conductor/pair configuration and continuous piece separately and not rely on storage location as proof.

Sources

Further reading

  1. Town of Cary — At Work
Call now